Stahl und Eisen

First Page  |  «  |  1  |  2  |  3 [ Go to bottom  |  Subscribe this forum  |  Create new topic ]


Title Replies Views Latest reply

Wenn man eine alte Feile...

by Strumpf on 11/02/2012 06:34 PM
28 13794 11/11/2012 04:13 PM
by naabthalschmied »

Analysewerte !!

by Damastschmied on 10/17/2011 07:25 PM
12 7281 11/01/2012 07:20 PM
by Klaeus »

Corten Vollmaterial/Rohr

by eisenkraut on 03/12/2012 06:14 PM
4 5788 10/18/2012 08:32 PM
by metallo »

Kann ich den Stahl nehmen

by Kingpin351 on 09/25/2012 01:00 PM
8 4027 09/27/2012 08:39 PM
by bummi »

Schraubfeder

by JS_78 on 08/29/2012 01:05 PM
9 5722 08/30/2012 08:24 PM
by EisenbahnPeter »

alte geschmiedete Kette

by Flo78 on 07/04/2012 07:37 AM
7 5384 07/09/2012 02:27 PM
by Flo78 »

Radreifen / Bodenfund

by Kauz on 06/19/2012 11:24 PM
12 6615 06/28/2012 06:59 AM
by Flo78 »

Blattfedern aufschmieden

by Micha on 06/19/2012 03:02 PM
12 11244 06/25/2012 07:47 AM
by Micha »

Brechstange härten?

by huj on 04/26/2012 12:07 PM
10 8302 04/27/2012 06:07 PM
by huj »

Bezugsquelle 75Ni8 gesucht

by Torsten on 04/21/2012 02:34 AM
7 5670 04/22/2012 08:15 AM
by akrumbsEisn »

Altes Eisen

by Klaeus on 03/22/2012 10:19 PM
6 4716 04/07/2012 07:13 PM
by Klaeus »

Funkenprobe

by Steff-for on 01/11/2012 04:13 PM
32 21897 03/04/2012 06:47 PM
by Damastschmied »

Wie wurden früher Sägeblätter hergestellt?

by Hoizhocka on 02/23/2012 09:27 PM
6 4080 02/25/2012 09:25 AM
by Warrior »

3 kilo sehr alter Stahl was könnte es sein

by Rebellenschmied on 01/08/2012 01:16 PM
26 9269 01/16/2012 07:26 PM
by Rebellenschmied »

Schienenstahl

by Willi on 11/16/2011 08:15 PM
10 7864 11/21/2011 04:04 PM
by Eisenbrenner »

Was ist C45E Werkstoffnummer 1.1191???

by Willi on 03/16/2011 12:07 PM
7 20670 11/16/2011 08:26 PM
by naabthalschmied »

Puddelstahl

by schakaa on 04/17/2011 10:47 AM
12 11133 10/17/2011 05:46 PM
by Klaeus »

Nicht nur Si-Stahl ist Federstahl

by Damastschmied on 06/20/2011 06:30 PM
8 6439 06/22/2011 03:53 PM
by Damastschmied »

First Page  |  «  |  1  |  2  |  3

« Back to overview